When your door needs torsion spring replacement, you want it done safely and right the first time. Typical jobs in Greeley, CO cost $200-$450, and you approve the price first. Torsion springs replaced and wound correctly, with high-cycle upgrades available.
Safety first: springs and cables hold hundreds of pounds of tension. Don't try to adjust or remove them yourself, and don't run the opener on a door that's crooked or has a broken spring.
When to call for torsion spring replacement
- A gap in the spring mounted on the bar above the door
- The door slams shut or won't stay open
- Only one side of the door lifts and the door goes crooked
- The door is suddenly too heavy to lift by hand
Common causes
- Normal fatigue at the end of the spring's rated cycles
- Rust or lack of lubrication
- An undersized spring working too hard
- A door that's been made heavier with insulation or new panels
What you can check yourself
- Count the springs above the door. Two-spring doors should have both replaced together.
- Look for rust or dry, squeaky coils, which are signs the spring is wearing out.
- Note how often the door is used each day so the right cycle rating can be chosen.
Still stuck? Our free symptom checker and troubleshooting wizard walk you through it step by step.
How we handle torsion spring replacement
- Clamp the door and unwind the old springs with proper winding bars
- Measure wire size, inside diameter and length, and weigh the door
- Install correctly rated springs, upgrading to high-cycle if you use the door a lot
- Wind to the right number of turns and set the door's balance
- Lubricate, adjust the cables and test the full travel
Wayne Dalton TorqueMaster doors keep the springs inside the torsion tube and need TorqueMaster-specific parts, which we can source.
Torsion Spring Replacement cost in Greeley, CO
What moves the price:
- Door size and weight (single or double, steel or wood)
- Which parts need replacing and whether they are in stock
- Spring type and cycle rating
- Emergency or after-hours timing
These are typical U.S. ranges, not a quote. You get an exact price for your door before any work starts. For a quick estimate, try the repair cost calculator.
Torsion Spring Replacement in Greeley, CO
In Colorado, cold mornings after mild afternoons put the most stress on worn springs, so breaks are common in late fall and winter.
Technicians serve all of Greeley (ZIP codes 80631, 80632, 80633, 80634, 80638 and more), plus Evans (3.4 mi), La Salle (5.2 mi), Eaton (7.4 mi) and Milliken (10.1 mi). Call (833) 435-8883 to book a visit in Greeley.
Torsion Spring Replacement: frequently asked questions
How much does torsion spring replacement cost in Greeley, CO?
Torsion Spring Replacement typically costs $200-$450 including parts and labor, and usually takes 1-2 hours. The exact price depends on your door and the parts it needs, and you get it before any work starts. Call (833) 435-8883 for a quote.
Can you do torsion spring replacement the same day?
Often, yes. When a technician is available we can usually come the same day, and common parts are carried on the truck. Doors that won't close or have a broken spring are treated as priority calls, and emergency service is available.
Is torsion spring replacement covered by a warranty?
Our work comes with a 90-day labor warranty on repairs. New parts and doors also carry the manufacturer's warranty. Ask for the warranty details in writing with your quote.
Are your technicians licensed and insured?
Our technicians are insured, and where Colorado or Greeley requires a contractor license for garage door work, the job is done under that license. You're welcome to ask for proof when you book.
Should I repair or replace my garage door?
A good rule of thumb: if the repair costs more than about 50% of a replacement, or the garage door is near the end of its life, replace it. A garage door typically lasts 15 to 30 years. If several panels are damaged, the door is rusted through or rotted, or parts are discontinued, replacing it is often better value. Springs are the exception: a broken spring is always replaced, never repaired. Our free repair vs. replace calculator can help you compare.